Showing posts with label Sciences. Show all posts
Showing posts with label Sciences. Show all posts

Tuesday, July 24, 2012

Intelegent Copilot For Car : Semiautonomous system takes the wheel to keep drivers safe

Barrels and cones dot an open field in Saline, Mich., forming an obstacle course for a modified vehicle. A driver remotely steers the vehicle through the course from a nearby location as a researcher looks on. Occasionally, the researcher instructs the driver to keep the wheel straight — a trajectory that appears to put the vehicle on a collision course with a barrel. Despite the driver’s actions, the vehicle steers itself around the obstacle, transitioning control back to the driver once the danger has passed.

The key to the maneuver is a new semiautonomous safety system developed by Sterling Anderson, a PhD student in MIT’s Department of Mechanical Engineering, and Karl Iagnemma, a principal research scientist in MIT’s Robotic Mobility Group.

The system uses an onboard camera and laser rangefinder to identify hazards in a vehicle’s environment. The team devised an algorithm to analyze the data and identify safe zones — avoiding, for example, barrels in a field, or other cars on a roadway. The system allows a driver to control the vehicle, only taking the wheel when the driver is about to exit a safe zone.

Anderson, who has been testing the system in Michigan since last September, describes it as an “intelligent co-pilot” that monitors a driver’s performance and makes behind-the-scenes adjustments to keep the vehicle from colliding with obstacles, or within a safe region of the environment, such as a lane or open area.

“The real innovation is enabling the car to share [control] with you,” Anderson says. “If you want to drive, it’ll just … make sure you don’t hit anything.”

The group presented details of the safety system recently at the Intelligent Vehicles Symposium in Spain.

Off the beaten path

Robotics research has focused in recent years on developing systems — from cars to medical equipment to industrial machinery — that can be controlled by either robots or humans. For the most part, such systems operate along preprogrammed paths.

As an example, Anderson points to the technology behind self-parking cars. To parallel park, a driver engages the technology by flipping a switch and taking his hands off the wheel. The car then parks itself, following a preplanned path based on the distance between neighboring cars.

While a planned path may work well in a parking situation, Anderson says when it comes to driving, one or even multiple paths is far too limiting.

“The problem is, humans don’t think that way,” Anderson says. “When you and I drive, [we don’t] choose just one path and obsessively follow it. Typically you and I see a lane or a parking lot, and we say, ‘Here is the field of safe travel, here’s the entire region of the roadway I can use, and I’m not going to worry about remaining on a specific line, as long as I’m safely on the roadway and I avoid collisions.’”

Anderson and Iagnemma integrated this human perspective into their robotic system. The team came up with an approach to identify safe zones, or “homotopies,” rather than specific paths of travel. Instead of mapping out individual paths along a roadway, the researchers divided a vehicle’s environment into triangles, with certain triangle edges representing an obstacle or a lane’s boundary.

The researchers devised an algorithm that “constrains” obstacle-abutting edges, allowing a driver to navigate across any triangle edge except those that are constrained. If a driver is in danger of crossing a constrained edge — for instance, if he’s fallen asleep at the wheel and is about to run into a barrier or obstacle — the system takes over, steering the car back into the safe zone.

Building trust

So far, the team has run more than 1,200 trials of the system, with few collisions; most of these occurred when glitches in the vehicle’s camera failed to identify an obstacle. For the most part, the system has successfully helped drivers avoid collisions.

Benjamin Saltsman, manager of intelligent truck vehicle technology and innovation at Eaton Corp., says the system has several advantages over fully autonomous variants such as the self-driving cars developed by Google and Ford. Such systems, he says, are loaded with expensive sensors, and require vast amounts of computation to plan out safe routes.

"The implications of [Anderson's] system is it makes it lighter in terms of sensors and computational requirements than what a fully autonomous vehicle would require," says Saltsman, who was not involved in the research. "This simplification makes it a lot less costly, and closer in terms of potential implementation."

In experiments, Anderson has also observed an interesting human response: Those who trust the system tend to perform better than those who don’t. For instance, when asked to hold the wheel straight, even in the face of a possible collision, drivers who trusted the system drove through the course more quickly and confidently than those who were wary of the system.

And what would the system feel like for someone who is unaware that it’s activated? “You would likely just think you’re a talented driver,” Anderson says. “You’d say, ‘Hey, I pulled this off,’ and you wouldn’t know that the car is changing things behind the scenes to make sure the vehicle remains safe, even if your inputs are not.”

He acknowledges that this isn’t necessarily a good thing, particularly for people just learning to drive; beginners may end up thinking they are better drivers than they actually are. Without negative feedback, these drivers can actually become less skilled and more dependent on assistance over time. On the other hand, Anderson says expert drivers may feel hemmed in by the safety system. He and Iagnemma are now exploring ways to tailor the system to various levels of driving experience.

The team is also hoping to pare down the system to identify obstacles using a single cellphone. “You could stick your cellphone on the dashboard, and it would use the camera, accelerometers and gyro to provide the feedback needed by the system,” Anderson says. “I think we’ll find better ways of doing it that will be simpler, cheaper and allow more users access to the technology.”

This research was supported by the United States Army Research Office and the Defense Advanced Research Projects Agency. The experimental platform was developed in collaboration with Quantum Signal LLC with assistance from James Walker, Steven Peters and Sisir Karumanchi.

Source : Jennifer, MIT News Office

Monday, July 16, 2012

Safety First : New Safety Technology

Volvo has been well renowned over the years for the safety of its vehicles and its development and research into its technologies. They were the innovators behind the three point seatbelt which they introduced in 1959, which is now standard across the vast majority of vehicles on the planet.

A more recent development from the Swedish car maker has been in the development of pedestrian airbags. The new Volvo V40 features seven sensors that when activated deploy airbags across the windshield to prevent a struck pedestrian from suffering head trauma.

Volvo are now taking it upon themselves to continue the innovation in areas such as autonomous driving support, intersection support and animal detection. Their aim is to eliminate deaths or serious injuries in Volvo cars by 2020.

Volvo’s autonomous driving support system will be able react in the event of an emergency and automatically adjust the car’s engine, brakes and steering. The system is designed to avoid collisions before they occur and to also help keep the car in the correct lane should the worst happen.

Intersection support will also use an array of vehicle sensors that are able to read the current road and traffic conditions. The system will apply the brakes if it deems that a collision at a junction or intersection is about to happen.

Volvo’s animal detection system is another technology Volvo will be looking to introduce into its fleet. In Sweden, accidents with animals typically occur at cruising speeds of 60mph, with impact speed being the determining factor in the damage and injuries sustained. The system will be able to detect animals from a distance of up to 30 metres away and apply the brakes automatically. Volvo hope that the system will be able to wipe off enough speed to help ensure that a collision does not incur any serious injuries.

With the current “compensation culture” in the UK, any technology that helps lifts the burden on insurers and motorists alike will be a welcome. Claims for Car accident compensation has resulted in premiums soaring the UK.

Monday, July 9, 2012

Computerize Identification For Oil and Gas Processing Plant


Current Bottlenecks of Oil and Gas Processing Companies

   For oil and gas companies, maintaining an operational integrity of the equipment and systems depends on the quality of monitoring, inspection and maintenance of the equipment (among others). But to date, efficiency of monitoring efforts is questionable as it requires considerable financial and human resources.
   Usually, during monitoring and inspection rounds the specialists first write down the monitored and measured parameters on the paper. Then, back at the workdesk, they again rewrite the collected information to the operational logs, or key it into the computer (usually in Excel table, less often into the MRO (Maintenance, Repair and Overhaul) programs.
   Such a “traditional” data collection procedure implies high degree of human error – there is no guarantee that the reporting specialist really completed the inspection and correctly noted the data. This means that reliability and accuracy of the received information, and, consequently, the operation of the facility, could be questioned.
   During the scheduled search for the best location for each facility according to given information, the personnel is forced to continually go back and forth, from the archive to the computer to check the database, as no-one can possibly keep the information about all monitored equipment in the head. Time wasted on moving and search for the necessary data takes at least 20 percent of the employees’ time (according to foreign estimates). That is, non-production costs are about six resource days per month or 70 resource days annually – this is a large figure, and the one that should attract attention of the management engaged in efficiency enhancement routines.
   This means that practically any facility of oil and gas processing industry is facing the tasks of reducing the impact of human factor on the quality of monitoring and maintenance, and improving the operating efficiency of personnel.

Boosting the performance gains

   Significant reduction of the resources used to maintain the normal functionality of equipment and engineering systems could be achieved by improving the following processes:
Timely information to staff and management on the status of equipment, any critical situations and, consequently, prevention of accidents, malfunctions and their prompt removal as required.
Monitoring operators’ activities by reducing the possibility of the following risks:
–    information loss (for example, loss of paper scratch-pad or the lack of a uniform standard for recording the monitored and measured parameters);
–    poor quality of work (i.e., careless writing in the scratch-pad);
–    failure to perform the routine maintenance (due to lack of formal means of maintenance monitoring).
Easy access to operational information and documentation.

The modern answer: computerized Identification and Information Mobility

   NEOLANT promptly responded to these market needs, unrolling its flagship information system based on the technology of automated identification and standing on the “three pillars”: 
barcode or radio frequency tagging of the monitored objects;
portable data terminals for the automated tag recognition, obtaining and entering real-time the information on the monitored equipment and subsequent information transfer to specialized information systems;
software for consolidating and processing the data, including data visualization tools (e.g., 3D models and geographic information systems).
The system provides ultimate control over the actions of operating personnel, the constant accumulation of relevant information about the equipment status, real-time expert access to all operational data independently of location.

Barcodes or RFID?

   Let’s consider the functioning of automated identification technology in detail.
Barcode tags (Fig. 1) are graphically encoded IDs of equipment. Special production and application method leads to the following results:
elimination of duplication;
virtually unlimited shelf life;
can be applied to almost any surface;
tags remain intact in the harshest operating environments.
In the application of radio frequency identification (RFID) data stored in the so-called RFID-tags are read and written by radio signals. This technology can do more complex tasks than barcoding; RFID-tags are more resistant to mechanical stress and pollution, and can be picked off by a scanner from a larger distance. Tags come in various forms: some contain only information stored by the manufacturer, others allow the customer to re-write data. However, the RFID system can be affected by electromagnetic fields.
The choice between the barcoding and RFID depends on the operating conditions at the customer’s plant - either technology has plus and minus points, and they complement each other well.
To read barcodes and RFID tags, portable data terminals (Fig. 2) are used. The device, a combination of handheld computer and scanner, guarantees the identification of the units, allows entering the current values of monitored parameters and storage of large amounts of information. The data terminals are equipped with touch screen, run NEOLANT-provided OS and have significant battery life (8-10 hours).

How Does the System Operate?

   Routine rounds, inspections, planned maintenance of equipment with automated identification (Fig. 3) can be divided into several stages:
Before starting the inspection the specialist identifies himself in the data terminal by user name and password. Without this procedure, the terminal will be unable to scan the bar codes, and hence data entry would be impossible. 
The terminal remembers the date and time of inspection.
The expert reads and decrypts the bar code tags with the terminal, which defines the class of a unit or component and identifies the specific tag.
After that the terminal offers to enter the current values of monitored equipment parameters, stores the values and provides access to expert information on past changes.
After the round the employee puts the terminal back in docking station attached to a PC. With the help of NEOLANT specialized software the data gets automatically transferred into the information system for analysis and processing. 
Further information can be printed or presented in any format: graphically, on technologic charts, in tables, reports, on the electronic map (GIS system) or on 3D model of the company, created by NEOLANT team.
Modern tag manufacturing technologies labels guarantee certain properties – i.e., the tags are impossible to remove or change without breaking. To scan the barcode, the employee must be near the monitored unit, and data entry option is available only after scanning is complete. This excludes the possibility of fake reports records and guarantees completion of routine maintenance rounds. Also, employee identification in the system and stored date and time of the inspection round ensure personal responsibility of operating personnel.

Information at Your Fingertips

   Another key advantage of automated identification technology is that mobile terminals significantly reduce time while adding up to the comfort of a planned maintenance. They allow storage and retrieval of information about the current state of company’s units, also giving the history of changes for monitored parameters and other data required by operators, up to route maps, guides and unit images.
All operating data and documentation collected in one device and available for reading at any location within the company on both HQ locations and in the field using secure Internet communication links. This means that personnel of operating units and services belongs to a single information space, to receives real-time information, updates it during the inspections, planned maintenance work, and does not waste time on unneeded movements within the company.

Monitoring Implies Visual Control

   A single information space created in NEOLANT system is supplemented by data visualization software - geographic information systems (GIS) and informational 3D models. The latter represent a 3D models of company facilities linked to relevant operational information and documentation; such models provide visual expert access to the data (by selecting objects on a 3D model). Visualization also helps business leaders to perceive information conveniently and clearly, for real-time troubleshooting and for reducing the risks associated with the human factor. 
3D model can reflect in a variety of data required by the manager or a technologist for the analysis of energy facilities and systems, such as:
the system uses color coding to indicate non-performance of a routine maintenance by the operating personnel, etc.;
the system visualizes the state of the facility, using color coding for highlighting segments of the model (Fig. 4), etc.
Usage of GIS systems to display information is advisable if the manager needs a comprehensive understanding of the status of equipment on large territories, or in geographical context.

The Problem Solved

   Automated identification technology helps to: 
prevent accidents and failures while ensuring timely repairs due to visualization of objects’ state in the information system and emergency alarm;
avoid loss of information due to data collection in electronic form directly at the location;
monitor the implementation of routine maintenance – tags are impossible to remove or change without breaking; also, there is visual alarm encoded into the 3D models;
ensure the quality of work through personal responsibility of each employee for their work of action and instant data transfer to the mangers via the 3D model;
provide convenient access to operational information through organization of operational data acquisition anywhere within the enterprise via mobile gadgets, organization and storage of operational data electronically in a single information system, and rendering with the use of 3D models or GIS systems.
NEOLANT proposes a complete cycle of works on creation of an automated identification system, from development of technical specifications, and to determine the optimal tag technology, customization, implementation, personnel training, tagging, equipment supply, creating 3D models, GIS networks, etc. Because each enterprise is unique, the company’s specialists develop, implement and adapt their solutions based on the specific situation.
Using the technology of automated identification, NEOLANT customers get a solution to the complex challenges they face – reducing the impact of human factor on the quality of monitoring and maintenance within the enterprises while improving the operating efficiency of personnel.

Work Place Heat Hazard

Hot environments in a wide range of industries present serious hazards to employee safety and health.  Heat stress, the combination of  heat, humidity and physical labor, can lead to serious illness and even death.


Long exposure to extreme heat or too much activity under a hot sun causes excessive perspiration, which can lead to heat exhaustion.  Symptoms include headache and a feeling of weakness and dizziness accompanied by nausea and vomiting, there may also be cramps.

In heat exhaustion there is excessive perspiration.  By contrast, in heat stroke, there is an absence of perspiration; an extremely high body temperature; hot, dry skin; confusion; and loss of consciousness and/or convulsions.  An extremely high body temperature can cause death.

Treatment for heat exhaustion includes:
  • Move the person to a cool environment (i.e. a well-ventilated or shaded area).
  • Remove or loosen their clothing.
  • Increase the consumption of fluids.  (Do not force an unconscious person to drink.)
For heat stroke or if the person is unconscious:
  • Reduce the body’s temperature as rapidly as possible via a cool water or sponge bath; fan the body surface.
  • Contact a physician immediately.

Case Study:  Restaurant Industry

In July of 2006, MIOSHA received an employee complaint regarding heat stress in a restaurant.  The complaint alleged that employees were working in 95-degree temperatures, they felt dehydrated, the temperature may have affected an employee’s breathing, an employee was sent to the emergency room for heat exhaustion, and the conditions were unworkable.

Investigation Background

While there are no MIOSHA regulations requiring temperatures to be kept under a certain degree, Section 11(a) of Act 154 (the General Duty Clause) requires the employer to furnish to each employee, employment and a place of employment which is free from recognized hazards that are causing, or are likely to cause, death or serious physical harm to the employee.

Work operations involving high air temperatures, radiant heat sources, high humidity, and strenuous physical work activities have a high potential for inducing heat stress in employees engaged in such operations.  The work operations identified in this investigation involved employees cooking at a grill in the kitchen, chefs cooking in the dining room, and workers dishwashing in the kitchen of a restaurant.  Employees had developed and experienced heat-induced disorders such as heat exhaustion, fainting and heat fatigue, for approximately two weeks prior to the investigation.

Investigation Measurements

During the investigation wet bulb globe temperature (WBGT) measurements were obtained.  WBGT offers a useful, first-order index of the environmental contribution to heat stress; it is influenced by air temperature, radiant heat and humidity, but does not account for all the interactions between an employee and the environment.

During the investigation the WBGT measurements indicated employees were exposed to readings ranging from 77.9 to 96.3 °F on July 28, 2006, and from 82.4 to 93.2 °F on August 2, 2006.  It was noted there were outdoor record high temperature of 96 °F on
July 31, 2006, and 97 °F on August 1, 2006.

Heat Stress Violations

The investigation of employee exposure to heat stress in this workplace resulted in a citation of the General Duty Clause being issued, based on known industry standards.

The American Conference of Governmental Industrial Hygienists (ACGIH®) provides general controls to deal with heat stress from air temperature, as well as the interactions between employees and the environment.  The interactions below were investigated during the inspection.

Heat reduction – During the investigation it was noted that employees were exposed to radiant heat during the cooking process and were exposed to steam while dishwashing.  The employer had not provided shielding, the ventilation above the dishwasher designed for removal of steam was not functioning, and cooling garments and portable air chillers were not utilized.

An employer should shield employees from radiant heat sources, and reduce process heat and water-vapor release.  Cooling garments (vests, bandanas) can be worn to reduce the heat exposure to employees and portable air chillers can be used. 

Ventilation – During the investigation it was noted that air conditioning was provided in the dining room and office areas, but there was no air conditioning supplied to the kitchen area for cooking and dishwashing.  It was also noted that the air conditioning in the dining room was not functioning at the time of the inspection.  Circulating fans were used in the kitchen areas; however, it was not effective since air that exceeds 95 °F can increase the heat load on the body.

An employer should provide general air movement through use of supply and exhaust ventilation.

Administrative controls – During the investigation it was noted that breaks were not taken by employees according to the ACGIH®recommendations for frequency found in Table 2 of the Heat Stress section of the Threshold Limit Values (TLV)booklet.  Employees were not allowed sufficient recovery time for heat exposure.  Breaks that were taken by dishwashers and dining room chefs were taken outdoors in a hot environment, not in a cool area.

An employer should set acceptable exposure times to heat, should allow sufficient recovery for employees exposed to heat, and should limit physiological strain by reducing heavy activity.  As metabolic rate increases from work demand, an employee’s exposure to heat stress can result in an excessive heart rate and elevated body core temperature by not allowing for proper recovery from heat exposure for the body.

Training – During the investigation it was noted that employees were not trained on the signs of symptoms of heat stress and were not permitted to practice self limitation to exposure.

Employers should train employees and supervisors by providing accurate verbal and written instructions about heat stress, including self-determination of exposures.  Employees should be aware of the signs and symptoms of heat stress and should be encouraged to detect these signs in themselves and in coworkers.  Employees should also be permitted to practice self limitation of heat exposure based on these signs.

Heat stress hygiene practices – During the investigation it was noted that most employees did drink water, but were not monitored or encouraged to drink cool water every 20 minutes.  Additionally, aside from the clothing worn by dishwashers, employees were required to wear uniforms that through fabric and style (high collars, neckties, and chef’s hats) limited evaporation.

Employers should encourage fluid replacement and the use of proper clothing.  Employees should drink small volumes (approximately 1 cup) of cool liquid every 20 minutes.  Free movement of cool, dry air over the skin’s surface maximizes heat removal through evaporation of sweat from the skin; water-vapor-impermeable or thermally insulated clothing restricts heat removal.

Medical surveillance – The investigation revealed the employer did not screen employees to identify those employees more susceptible to heat.

Employers should allow pre-placement screening to identify those employees susceptible to systemic heat injury.  Employees who take medications that may compromise normal cardiovascular, blood pressure, body temperature regulation, renal or sweat gland functions; and those employees who abuse alcohol, may have an increased susceptibility to heat stress.  Employers can also encourage healthy life styles and ideal body weight.

Acclimatization – During the investigation it was noted the employees were acclimated to the heat exposure.

Acclimatization is a gradual physiological adaptation that improves an individual’s ability to tolerate heat stress.  Full-heat acclimatization requires up to three weeks of continued physical activity under heat-stress conditions similar to those anticipated for the work, with a loss occurring after four days.  Employers can develop a plan to expose employees to heat at gradually increasing rate over a five-day period. 

Company Abatement

The employer submitted the information below as actions taken to address the issue:

  • Air conditioning equipment in restaurant was repaired.
  • Cooling vests and cooling bandanas were purchased for employees.
  • Temperature monitoring control devices were purchased and place in the kitchen and dining room.
  • A temperature monitoring and tracking procedure was implemented.
  • Management attended a MIOSHA safety in the workplace seminar.
  • Signs were posted educating the staff about heat stress and how to recognize the symptoms in themselves and others.
  • Employees were given access to cool beverages.
  • Major renovations of the building which would include replacing HVAC equipment were planned.
CET Division Services

If you have any questions on heat stress, or need a workplace evaluation, please call the MIOSHA Consultation Education and Training (CET) Division at 517.322.1809. 
Additional information and handouts can be obtained from www.michigan.gov/miosha;  www.osha.gov; and www.cdc.gov/niosh/topics/heatstress.

Friday, May 18, 2012

What is Hot Tapping ? : safety/hot-tapping


What is a Hot Tap and why it is made?

Hot Taps or Hot Tapping is the ability to safely tie into a pressurized system, by drilling or cutting, while it is on stream and under pressure.

Typical connections consist:
  • Tapping fittings like Weldolet®, Reinforced Branch or Split Tee.
  • Split Tees often to be used as branch and main pipe has the same diameters.
  • Isolation Valve like gate or Ball Valve.
  • Hot tapping machine which includes the cutter, and housing.
Mechanical fittings may be used for making hot taps on pipelines and mains provided they are designed for the operating pressure of the pipeline or main, and are suitable for the purpose.
  • Design: ANSI B31.1, B31.3, ANSI B31.4 & B31.8, ASME Sec. VIII Div.1 & 2
  • Fabrication: ASME Sec. VIII Div.1
  • Welding: ASME Sec. IX
  • NDT: ASME Sec. V
There are many reasons to made a Hot Tap. While is preferred to install nozzles during a turnaround, installing a nozzle with equipment in operation is sometimes advantageous, especially if it averts a costly shut down. 

Remarks before made a Hot Tap
  • A hot tap shall not be considered a routine procedure, but shall be used only when there is no practical alternative.
  • Hot Taps shall be installed by trained and experienced crews.
  • It should be noted that hot tapping of sour gas lines presents special health and metallurgical concerns and shall be done only to written operating company approved plans.
  • For each hottap shall be ensured that the pipe that is drilled or sawed has sufficient wall thickness, which can be measured with ultrasonic thickness gauges. The existing pipe wall thickness (actual) needs to be at least equal to the required thickness for pressure plus a reasonable thickness allowance for welding. If the actual thickness is barely more than that required for pressure, then loss of containment at the weld pool is a risk.
  • Welding on in-service pipelines requires weld procedure development and qualification, as well as a highly trained workforce to ensure integrity of welds when pipelines are operating at full pressure and under full flow conditions. 

Hot Tap setup

For a hot tap, there are three key components necessary to safely drill into a pipe; the fitting, the Valve, and the hot tap machine. The fitting is attached to the pipe, mostly by welding. In many cases, the fitting is a Weldolet® where a flange is welded, or a split tee with a flanged outlet (see image above).

Onto this fitting, a Valve is attached, and the hot tap machine is attached to the Valve (see images on the right). For hot taps, new studbolts, gaskets and a new Valve should always be used when that components will become part of the permanent facilities and equipment.

The fitting/Valve combination, is attached to the pipe, and is normally pressure tested. The pressure test is very important, so as to make sure that there are no structural problems with the fitting, and so that there are no leaks in the welds.

The hot tap cutter, is a specialized type of hole saw, with a pilot bit in the middle, mounted inside of a hot tap adapter housing.

The hot tap cutter is attached to a cutter holder, with the pilot bit, and is attached to the working end of the hot tap machine, so that it fits into the inside of the tapping adapter. The tapping adapter will contain the pressure of the pipe system, while the pipe is being cut, it houses the cutter, and cutter holder, and bolts to the Valve.

Hot Tap operation

The Hot Tap is made in one continuous process, the machine is started, and the cut continues, until the cutter passes through the pipe wall, resulting in the removal of a section of pipe, known as the "coupon". The coupon is normally retained on one or more u-wires, which are attached to the pilot bit. Once the cutter has cut through the pipe, the hot tap machine is stopped, the cutter is retracted into the hot tap adapter, and the Valve is closed.

Pressure is bled off from the inside of the Tapping Adapter, so that the hot tap machine can be removed from the line. The machine is removed from the line, and the new service is established.

Hot Tap Coupon

The Coupon, is the section of pipe that is removed, to establish service. It is very highly desirable to "retain" the coupon, and remove it from the pipe, and in the vast majority of hot taps, this is the case. Please note, short of not performing the hot tap, there is no way to absolutely guarantee that the coupon will not be "dropped".

Coupon retention is mostly the "job" of the u-wires. These are wires which run through the pilot bit, and are cut and bent, so that they can fold back against the bit, into a relief area milled into the bit, and then fold out, when the pilot bit has cut through the pipe.

In almost all cases, multiple u-wires are used, to act as insurance against losing the coupon.

Line Stopping

Line Stops, sometimes called Stopples (Stopple® is a trademark of TD Williamson Company) start with a hot tap, but are intended to stop the flow in the pipe. Line Stops are of necessity, somewhat more complicated than normal hot taps, but they start out in much the same way. A fitting is attached to the pipe, a hot tap is performed as previously detailed. Once the hot tap has been completed, the Valve is closed, then another machine, known as a line stop actuator is installed on the pipe. The line stop actuator is used to insert a plugging head into the pipe, the most common type being a pivot head mechanism. Line stops are used to replace Valves, fittings and other equipment. Once the job is done, pressure is equalized, and the line stop head is removed. The Line Stop Fitting has a specially modified flange, which includes a special plug, that allows for removal of the Valve. There are several different designs for these flanges, but they all work pretty much the same, the plug is inserted into the flange through the Valve, it is securely locked in place, with the result that the pressure can be bled off of the housing and Valve, the Valve can then be removed, and the flange blinded off.

Line Stop setup

The Line Stop Setup includes the hot tap machine, plus an additional piece of equipment, a line stop actuator. The Line Stop Actuator can be either mechanical (screw type), or hydraulic, it is used, to place the line stop head into the line, therefore stopping the flow in the line.

The Line Stop Actuator is bolted to a Line Stop Housing, which has to be long enough to include the line stop head (pivot head, or folding head), so that the Line Stop Actuator, and Housing, can be bolted to the line stop Valve. Line stops often utilize special Valves, called Sandwich Valves.

Line Stops are normally performed through rental Valves, owned by the service company who performs the work, once the work is completed, the fitting will remain on the pipe, but the Valve and all other equipment is removed.

Line Stop operation

A Line Stop starts out the same way as does a Hot Tap, but a larger cutter is used,. The larger hole in the pipe, allows the line stop head to fit into the pipe. Once the cut is made, the Valve is closed the hot tap machine is removed from the line, and a line stop actuator is bolted into place.

New gaskets are always to be used for every setup, but "used" studs and nuts are often used, because this operation is a temporary operation, the Valve, machine, and actuator are removed at the end of the job. New studs, nuts, and gaskets should be used on the final completion, when a blind flange is installed outside of the completion plug.

The line stop actuator is operated, to push the plugging head (line stop head), down, into the pipe, the common pivot head, will pivot in the direction of the flow, and form a stop, thus stopping the flow in the pipe.

Completion Plug

In order to remove the Valve used for line stop operations, a completion plug is set into the line stop fitting flange (Completion Flange).

There are several different types of completion flange/plug sets, but they all operate in basically the same manner, the completion plug and flange are manufactured, so as to allow the flange, to accept and lock into place, a completion plug.

This completion plug is set below the Valve, once set, pressure above the plug can be bled off, and the Valve can then be removed.

Once the plug has been properly positioned, it is locked into place with the lock ring segments, this prevents plug movement, with the o-ring becoming the primary seal.

Wednesday, May 9, 2012

S - Safety: CPR /Safety

Cardiopulmonary resuscitation (CPR) is an emergency procedure which is performed in an effort to manually preserve intact brain function until further measures are taken to restore spontaneous blood circulation and breathing in a person in cardiac arrest. It is indicated in those who are unresponsive with no breathing or abnormal breathing, for example agonal respirations. It may be performed both in and outside of a hospital.

CPR involves chest compressions at least 5 cm deep and at a rate of at least 100 per minute in an effort to create artificial circulation by manually pumping blood through the heart. In addition, the rescuer may provide breaths by either exhaling into the subject's mouth or utilizing a device that pushes air into the subject's lungs. This process of externally providing ventilation is termed artificial respiration. Current recommendations place emphasis on high-quality chest compressions over artificial respiration; a simplified CPR method involving chest compressions only is recommended for untrained rescuers.

CPR alone is unlikely to restart the heart; its main purpose is to restore partial flow of oxygenated blood to the brain and heart. The objective is to delay tissue death and to extend the brief window of opportunity for a successful resuscitation without permanent brain damage. Administration of an electric shock to the subject's heart, termed defibrillation, is usually needed in order to restore a viable or "perfusing" heart rhythm. Defibrillation is only effective for certain heart rhythms, namely ventricular fibrillation or pulseless ventricular tachycardia, rather than asystole or pulseless electrical activity. CPR may succeed in inducing a heart rhythm which may be shockable. CPR is generally continued until the subject regains return of spontaneous circulation (ROSC) or is declared dead.

Medical uses

CPR is indicated for any person who is unresponsive with no breathing, or who is only breathing in occasional agonal gasps, as it is most likely that they are in cardiac arrest.S643 If a person still has a pulse, but is not breathing (respiratory arrest), artificial respirations may be more appropriate, but due to the difficulty people have in accurately assessing the presence or absence of a pulse, CPR guidelines recommend that lay persons should not be instructed to check the pulse, while giving health care professionals the option to check a pulse.In those with cardiac arrest due to trauma CPR is considered futile in the pulseless case, but still recommended for correctible causes of arrest.

Standard

A universal compression to ventilation ratio of 30:2 is recommended.[5]:8 With children, if at least 2 rescuers are present a ratio of 15:2 is preferred.[5]:8 In newborns a rate of 3:1 is recommended unless a cardiac cause is known in which case a 15:2 ratio is reasonable.If an advanced airway such as an endotracheal tube or laryngeal mask airway is in place delivery of respirations should occur without pauses in compressions at a rate of 8–10 per minute.The recommended order of interventions is chest compressions, airway, breathing or CAB in most situations,with a compression rate of at least 100 per minute in all groups.Recommended compression depth in adults and children is about 5 cm (2 inches) and in infants it is 4 cm (1.5 inches).As of 2010 the Resuscitation Council (UK) still recommends ABC for children.As it can be difficult to determine the presence or absence of a pulse the pulse check has been removed for lay providers and should not be performed for more than 10 seconds by health care providers.In adults rescuers should use two hands for the chest compressions, while in children they should use one, and with infants two fingers (index and middle fingers).

Compression only

Compression only (hands-only or cardiocerebral resuscitation) CPR is a technique that involves chest compressions without artificial respiration.It is recommended as the method of choice for the untrained rescuer or those who are not proficient as it is easier to perform and instructions are easier to give over the phone.In adults with out-of-hospital cardiac arrest, compression-only CPR by the lay public has a higher success rate than standard CPR.The exceptions are cases of drownings, drug overdose, and arrest in children. Children who receive compression only CPR have the same outcomes as those who received no CPR.The method of delivering chest compressions remains the same, as does the rate (at least 100 per minute). It is hoped that the use of compression only delivery will increase the chances of the lay public delivering CPR.As per the American Heart Association, the beat of the Bee Gees' song Stayin' Alive provides an ideal amount of beats-per-minute to use for hands-only CPR.For those with non cardiac arrest and people less than 20 years of age standard CPR is superior to compression only CPR.

In pregnancy

During pregnancy when a woman is lying on her back the uterus may compress the inferior vena cava and thus decrease venous return.It is recommended for this reason that the uterus be pushed to the woman's left and if this is not effective either roll the person 30° or consider emergency cesarean section. Other

Interposed abdominal compressions may be beneficial in the hospital environment. There is however no evidence of benefit pre hospital or in children.Internal cardiac massage is manual squeezing of the heart carried out through a surgical incision into the chest cavity. This may be carried out if the chest is already open for cardiac surgery.

Effectiveness

Used alone, CPR will result in few complete recoveries, and those who do survive often develop serious complications. Estimates vary, but many organizations stress that CPR does not "bring anyone back," it simply preserves the body for defibrillation and advanced life support.However, in the case of "non-shockable" rhythms such as Pulseless Electrical Activity (PEA), defibrillation is not indicated, and the importance of CPR rises. On average, only 5–10% of people who receive CPR survive.The purpose of CPR is not to "start" the heart, but rather to circulate oxygenated blood, and keep the brain alive until advanced care (especially defibrillation) can be initiated. As many of these patients may have a pulse that is impalpable by the layperson rescuer, the current consensus is to perform CPR on a patient who is not breathing.

Studies have shown that immediate CPR followed by defibrillation within 3–5 minutes of sudden VF cardiac arrest improves survival. In cities such as Seattle where CPR training is widespread and defibrillation by EMS personnel follows quickly, the survival rate is about 30 percent. In cities such as New York, without those advantages, the survival rate is only 1–2 percent.

In most cases, there is a higher proportion of patients who achieve a Return of Spontaneous Circulation (ROSC), where their heart starts to beat on its own again, than ultimately survive to be discharged from hospital (see table below). This is due to medical staff either being ultimately unable to address the cause of the arrhythmia or cardiac arrest, or in some instances due to other co-morbidities, due to the patient being gravely ill in more than one way.

Compression-only CPR is less effective in children than in adults, as cardiac arrest in children is more likely to have a non-cardiac cause. In a 2010 prospective study of cardiac arrest in children (age 1–17), for arrests with a non-cardiac cause, provision by bystanders of conventional CPR with rescue breathing yielded a favorable neurological outcome at one month more often than did compression-only CPR (OR 5.54; 95% confidence interval 2.52–16.99). For arrests with a cardiac cause in this cohort, there was no difference between the two techniques (OR 1.20; 95% confidence interval 0.55–2.66).This is consistent with American Heart Association guidelines for parents.

Wednesday, May 2, 2012

Seo Safety Moz : Function Of Flare Stack

A gas flare, alternatively known as a flare stack, is an elevated vertical conveyance found accompanying the presence of oil wells, gas wells, rigs, refineries, chemical plants, natural gas plants, and landfills.

They are used to eliminate waste gas which is otherwise not feasible to use or transport. They also act as safety systems for non-waste gas and is released via pressure relief valve when needed to ease the strain on equipment. They protect gas processing equipment from being overpressured. Also in case of an emergency situation, the flare system helps burn out the total reserve gas.

However, flaring poses the serious problem of wasting energy uselessly. Flaring basically consists in burning precious resources instead of using them. It also plays a role in the increase of CO2 emissions.

Function

On oil production rigs, in refineries and chemical plants, its primary purpose is to act as a safety device to protect vessels or pipes from over-pressuring due to unplanned upsets. Pressure control valves are set at predetermined pressures to release excess gas, thus allowing continued operation during upset conditions. Whenever plant equipment items are over-pressured, the pressure relief valves on the equipment automatically release gases (and sometimes liquids as well) which are routed through piping runs called flare headers to the flare stacks.

The gases and/or liquids are separated in a flare knock out drum with the gas piped to the flare stacks for burning or for lighter gases venting. The size and brightness of the resulting flame depends upon how much flammable material was released. Typically there may be more than one flare system handling high pressure gas, low pressure gas, sour or corrosive gas, cold gas and wet gas. Vents (unignited flares) are used typically on gas plants for emergency gas disposal and are designed to operate in an emergency at sonic velocity.

Flare gas recovery systems are occasionally used to collect low flows of waste gas and return it to the Process Plant as opposed to burning the gas. Steam can be injected into the flame to reduce the formation of black smoke. The injected steam does however make the burning of gas sound louder, which can cause complaints from nearby residents. Compared to the emission of black smoke, it can be seen as a valid trade off. In order to keep the flare system functional, a small amount of purge gas flows continuously, whilst there are continuously burning pilots, so that the system is always ready for its primary purpose of burning as an over-pressure safety system. Enclosed ground flares are engineered to eliminate toxic and corrosive components, reduce smoke, and contain the flame within the enclosure. Burn pits are used to dispose of waste hydrocarbon liquids and are increasingly being designed out due to their unacceptable dirty appearance.